Announcement

Collapse
No announcement yet.

How to Zero a Handgun Laser

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    How to Zero a Handgun Laser

    How to Zero a Handgun Laser

    Twenty-five years ago, the idea of mounting a laser optic on a handgun seemed radical, and laser sights were largely dismissed as unnecessary gadgets. Since that time, perception has changed dramatically, and today more shooters are adding laser optics to their firearms.

    Lasers are relatively simple to install, especially with rail systems on modern pistols. However, correctly zeroing a handgun laser differs slightly from zeroing iron sights. While it is not difficult to mount and sight in a laser, it can cause problems if done incorrectly.

    For a laser to function properly, you need to understand the sight-in process and avoid pitfalls that can cost you time and ammunition. Here is a simple five-step method to ensure that the laser you mount is ready to perform.

    Step 1: Install the Laser
    This may sound very basic, but these are the most common problems I’ve seen with firearms-mounted lasers. Many lasers fit on your gun’s accessory rail using an adapter plate that provides a stable mounting platform. Oftentimes, shooters who hastily mount the laser on the gun fail to ensure a solid fit, and that can lead to horrible accuracy.

    While mounting a Crimson Trace laser, I noticed that all but one of the plates provided would fit in the gun’s accessory rail, though only one plate (the one prescribed for use on my gun by the factory) allowed for a stable mount. In addition, the side screws need to be secure, tight enough to hold the laser firmly in place on the accessory rail without allowing any movement. I’ve fixed two “malfunctioning” lasers for others, and in both cases it was operator error that resulted in poor accuracy.

    Step 2: Get On-Target From A Rest
    You can save yourself a lot of headache and ammunition by zeroing your laser from a fixed rest rather than banging away at the board while intermittently adjusting the laser’s point-of-impact. In fact, you should be able to quickly adjust the laser and be pretty close to on-target without firing a single shot.

    Before you begin fine-tuning the laser, have the owner’s manual on hand to tell you which direction you turn the sighting screws for left/right, up/down windage and elevation adjustments. You don’t want to start playing the “wrong way” game at the range.

    I also make sure to bring a portable Tipton gun vise in case I need to make any adjustments, and it’s perfect for getting a laser close to center after mounting. The vise allows me to hold the handgun secure while I align the laser and iron sights with the laser tools provided.

    This is a much easier way to get on target than shooting, adjusting, shooting and readjusting. It takes a little extra time, but when you fire your first shot, you should only have to fine-tune the point of impact, nothing more.

    Step 3: Sight In At Longer Range
    The temptation when mounting a laser on a defensive handgun is to sight in at the range you expect to shoot. It makes sense, but that’s a mistake.

    Let’s say that the popular belief that most gunfights occur at about 10 feet is true, and you align your laser so that it is dead-on at that range. It will work well at that distance, but keep in mind that the laser itself is mounted well under the barrel (or, in the case of hand grips, to the side of your barrel), so the angle required to get on target is pretty steep.

    That also means that at 15, 20 and 25 feet, the path of the laser continues to rise. As the distance increases, you will be farther off target. Suddenly, you’ll be missing the target and won’t understand why. Instead, sight in at 25 feet. The laser’s point of impact shift will be more gradual, and even at close range you won’t be more than an inch or so off target.

    Step 4: Make Minor Adjustments
    Most lasers don’t have ¼ MOA adjustments, meaning you’re often adjusting the laser by feel. When adjusting your laser, think small. Because lasers allow for a wide range of POI adjustments utilizing a limited amount of space for fine tuning, it’s easy to overcompensate and find yourself seesawing between left of center and right of center or high and low.

    Step 5: Shoot Plenty of Rounds
    When your laser is mounted and sighted, don’t simply shove the gun in a safe or stick it into your holster and head out.

    You need plenty of range time with a laser for two primary reasons:
    1. Ensure the laser is firmly planted on your gun and won’t shake loose with recoil or daily handling.
    2. Feel completely comfortable with the laser system. It’s important to know that your laser is properly sighted, but it’s equally important to be sure the laser works on your gun.

    After a period of a hundred rounds or more, it’s also time to check the screws and ensure the laser is still properly secured. If you installed it properly there shouldn’t be a problem, but the screws may back out just a bit and this is the time to know about it. If your laser stands up to a few hundred rounds and passes the inspection, there’s a very good chance the laser will be there when you need it. If you’ve fired enough rounds to verify the unit is secure, you’ve already started developing the muscle memory needed to shoot accurately in a stressful situation.

    Final Tip: Use the ammo you intend to carry while sighting in the laser.

    http://www.handgunsmag.com/how-to/ho...ntent=handguns
    Pat ------> NRA Endowment Member

    #2
    Step 3 is KEY. I had a friend who was bore sighting in an AR with a bore laser and was using a wall 8' away. He was complaining the front sight post wouldn't go any lower. I tried to explain that he was WAY too close to sight in as the round would be well over 18" high at even 25 yards.
    Bullets have a ballistic profile and do not fly straight. Just becasue you can see your target doesn't always mean you can hit it due to the bullet arc and overhead obstacles.
    Good advice.

    Comment


      #3
      Hmmm. Selfishly hoping this stirs some interest as I have a Viridian CL5 that is going to show up in the classifieds as soon as I can take some photos of it

      Comment


        #4
        Pretty much the same deal when adjusting scopes and red dots. A 50 yard zero will shoot low at matches where many targets are no more than 15 yards or point blank range.
        SHADAP VARMINT!

        Comment

        Working...
        X